eduPhysics

To Draw the Characteristic Curve of a Forward Biased p-n Junction Diode and Determine its Static and Dynamic Resistance

Class 12 Physics Practical · NIOS / CBSE ·eduPhysics- Excellence in Physics Education

Aim

To draw the V–I characteristic curve of a p-n junction diode in forward bias and reverse bias (Zener breakdown), and to determine its static (DC) and dynamic (AC) resistance from the graph.

Apparatus

Silicon p-n junction diode (1N4007) for the forward study, a 5.1 V Zener diode (e.g. BZX55C5V1) for the reverse study, 0–3 V DC source (forward) and 0–12 V variable DC supply (reverse), rheostat (about 100 Ω), 470 Ω protective resistor, voltmeter (0–1 V forward, 0–10 V reverse), milliammeter (0–30 mA), microammeter (0–1000 µA), one-way key, connecting wires, sandpaper and graph paper.

Theory

A p-n junction diode conducts easily when the p-side is connected to the positive terminal of the source (forward bias) and hardly conducts when connected oppositely (reverse bias). In forward bias, current stays almost zero until the applied voltage crosses the knee (threshold) voltage, about 0.7 V for silicon and 0.3 V for germanium; after this it rises sharply.

In reverse bias only a tiny, almost steady leakage current of a few µA flows. When the reverse voltage reaches the Zener breakdown voltage V<sub>z</sub>, the junction breaks down and the current increases steeply while the voltage across the diode stays nearly constant.

Static resistance: Rs = V / I at a chosen point of the curve.

Dynamic resistance: rd = ΔV / ΔI (reciprocal of the slope of the curve at that point).

Circuit Diagram

Circuit for the forward bias characteristic

The rheostat acts as a potential divider. The voltmeter is connected across the diode and the milliammeter in series with it. For reverse bias, connect the Zener diode with its n-end (cathode) to the positive terminal, replace the milliammeter by a microammeter, and keep the 470 Ω protective resistor in series.

Procedure

  1. Connect the circuit as shown, with the p-end of the diode towards the positive terminal. Rub the wire ends clean with sandpaper.
  2. Note the least count and zero error of each meter.
  3. With the rheostat at minimum output, close the key and increase the voltage in steps of 0.1 V up to 0.5 V, then in steps of 0.02 V.
  4. Record the voltmeter and milliammeter readings every time. Do not exceed the rated diode current.
  5. Connect the Zener diode in reverse bias with the microammeter. Increase the reverse voltage in steps of 1 V up to 4 V, then in steps of 0.1 V near breakdown, and note the steady microcurrent and the voltage at which the current suddenly rises. Stop when the current reaches about 600 µA.
  6. Plot the graphs and calculate the resistances.

Observations

Table 1: Forward bias (silicon diode)

S.No. Voltage V (V) Current I (mA) V/I (Ω)
1 0.00 0.0 —
2 0.10 0.0 —
3 0.20 0.0 —
4 0.30 0.0 —
5 0.40 0.0 —
6 0.50 0.1 5000
7 0.55 0.3 1833
8 0.60 0.9 667
9 0.62 1.4 443
10 0.64 2.2 291
11 0.66 3.4 194
12 0.68 5.2 131
13 0.70 8.0 88
14 0.72 12.0 60

Table 2: Reverse bias (5.1 V Zener diode)

S.No. Reverse voltage V (V) Reverse current I (µA) Region
1 0 0 Steady leakage
2 1 1 Steady leakage
3 2 1.5 Steady leakage
4 3 1.8 Steady leakage
5 4 2 Steady leakage
6 4.5 2 Steady leakage
7 4.8 2.1 Steady leakage
8 5 2.3 Steady leakage
9 5.1 4 Knee (Zener voltage)
10 5.2 25 Zener breakdown
11 5.3 90 Zener breakdown
12 5.4 260 Zener breakdown
13 5.5 600 Zener breakdown

Sample readings for a typical 1N4007 (forward) and a 5.1 V Zener diode (reverse). An ordinary 1N4007 does not break down at these voltages. Record your own actual readings in the lab.

Graph: Forward Bias Characteristics

Graph for forward bias characteristics of a diode

Graph: Reverse bias Characteristics

Reverse bias V-I characteristics of Silicon Diode

Graph: Combined V–I Characteristic

Forward and reverse characteristics are shown on a single graph. The forward side uses mA and the reverse side µA, and each side has its own voltage scale.

Combined V-I Characteristics of a Diode
Forward characteristics curve with construction for static and dynamic resistance

Calculations

Static resistance at P (V = 0.70 V, I = 8.0 mA):

Rs = 0.70 / (8.0 × 10−3) = 87.5 Ω

Dynamic resistance about P, with ΔV = 0.72 − 0.68 = 0.04 V and ΔI = 12.0 − 5.2 = 6.8 mA:

rd = 0.04 / (6.8 × 10−3) = 5.9 Ω

Result

  • The forward curve is non-linear; the knee voltage is about 0.6–0.7 V.
  • Static resistance at 0.70 V is 87.5 Ω.
  • Dynamic resistance at 0.70 V is 5.9 Ω, much smaller than the static value.
  • In reverse bias the current stays steady at about 2 µA up to about 5.0 V.
  • Zener breakdown voltage V<sub>z</sub> ≈ 5.1 V; beyond it the current rises steeply (from about 4 µA to 600 µA within 0.4 V).

Precautions and Sources of Error

  • Check all connections and meter zero errors before starting.
  • Never exceed the maximum forward current of the diode.
  • In reverse bias keep the protective resistor in series and do not let the current exceed the Zener’s rated limit.
  • Increase voltage gradually, with small steps near the knee.
  • Keep the diode at constant temperature; heating changes the readings.

Viva Voce

Q1. Why is the forward curve non-linear? The diode does not obey Ohm’s law; its resistance changes with voltage.

Q2. What is the knee voltage? The forward voltage beyond which current rises rapidly.

Q3. Which is greater, static or dynamic resistance? In the forward region, static resistance is greater.

Q4. Why is a rheostat used as a potential divider? To vary the voltage smoothly from zero.

Q5. What is Zener breakdown? The sudden, steep rise in reverse current at a particular reverse voltage, with the voltage across the diode nearly constant.

Q6. Why is the reverse current steady before breakdown? It is due to minority charge carriers, which hardly depend on the applied voltage.


Discover more from eduPhysics

Subscribe to get the latest posts sent to your email.

Discover more from eduPhysics

Subscribe now to keep reading and get access to the full archive.

Continue reading